AUTONET TV

Go With the Flow (MAF Sensor Replacement)

A driver brought her vehicle into the shop the other day and told us how she was getting lousy fuel economy and that the engine was running rough.  Plus, the Check Engine light was on.  Our technician checked the code the engine had generated (why the Check Engine light was on) and found the problem.  It was a faulty Mass Air Flow sensor, MAF sensor for short.

This MAF sensor is an important part of your vehicle.  What it does is calculate the amount of air going into your engine.  As you may know, air is taken into your engine where it's mixed with fuel.  Then, the spark plugs fire, that explosive fuel/air mixture detonates, and all these sequential explosions together provide the power to get your vehicle moving down the road. 

It makes sense that if the MAF sensor isn't sending the engine's computers the correct information on the amount of air going in the engine, the fuel/air mixture isn't going to be right. It will either too rich (too much gasoline for the amount of air) or too lean (not enough gasoline for the amount of air).

In this driver's case, the MAF sensor was damaged and needed to be replaced.  Another thing that may cause the MAF to give an incorrect reading is if its wires are dirty or faulty.  So, replacing or cleaning the wires important as well.

Other symptoms that your MAF sensor is bad? If your engine hesitates when you step on the gas, it stalls, or your vehicle is jerky when you accelerate. 

A malfunctioning MAF sensor is not just bad for performance.  Driving with your vehicle in that condition can cause more damage to your engine.  When you bring your vehicle in for us to check, a technician will thoroughly examine your engine to make sure all issues are taken care of.

Arizona Auto and Radiator Repair
1255 E FRY BLVD
Sierra Vista, AZ 85635
520-459-2216
http://www.azautorepair.net

Snake in the Engine (Serpentine Belt)

There's a belt that snakes through your engine.  It's even named for a snake, the serpentine belt.  It'll bite you when it breaks, possibly leaving you stranded.  So, it's good to know a little about this snake-like belt.

In early engines, there were lots of belts. They were used to convert the rotating power of the engine to turn a mechanical part.  But engineers had an idea.  Why not consolidate all those belts into one that ran a bunch of different parts simultaneously? Voila!  The serpentine belt.

It's found in the front or side of your engine unlike older belts which were often in a V shape, the serpentine belt has ribs on it which more effectively connect with the pulleys that power the other components.  A serpentine belt may power the water pump, power steering pump, alternator, and the air conditioning: all from one crankshaft. 

Now, all that's fine when everything is working well and the belt is intact.  But when a serpentine belt wears, gets loose, or breaks, it can affect many engine components at once.  Not an ideal situation. 

If you hear squeals coming from the engine compartment, see a battery light, or the engine overheats, those could be signs that your serpentine belt needs replacing.

The good news is that they usually last a long time, from 60,000-100,000 miles or 100,000-160,000 km.  Still, they don't last forever, and your vehicle's manufacturer usually recommends replacing them when they've gone close to the expected maximum.  It’s also recommended that you replace the pulleys and belt tensioner at the same time as they have the same service life. Regular maintenance and inspection of the serpentine belt is not only a good idea; it’s one of those things that you should not let "slip" by.

Arizona Auto and Radiator Repair
1255 E FRY BLVD
Sierra Vista, AZ 85635
520-459-2216
http://www.azautorepair.net

Oil's Well That Ends Well (Oil Change Grades and Weight)

Changing your oil regularly is one of the most important things you can do to keep your vehicle running well.  And knowing the right type of oil to use is also very important. 

Engine oil is classified by weight, but it doesn't refer to how much the oil would weigh if you put it on a scale.  It refers to viscosity, or how easily the oil flows through the engine.  Most engines operate normally at around 210°F/99°C.  The viscosity, or weight, is assigned a number by how well it flows at that temperature.  The lower the number, the more freely it flows. 

Most vehicle engines use what's called a multigrade oil which behaves differently in different temperatures. Multigrade oils have a "W" in their viscosity number that you may have seen on a bottle of oil, something like 5W30.  The W stands for winter and shows how freely it flows in colder temperatures.

That means a 5W30 oil will behave like a 5 weight oil in lower temperatures (less viscous or thinner) and a 30 weight oil in warmer temperatures (more viscous or thicker).  That's important on a cold day because the oil needs to behave like a thinner oil when you start your engine since it need to lubricate engine components immediately to protect the metal components. Then as the engine warms up, it behaves like a thicker oil to prevent friction among those parts.  Pretty neat trick, right?

The type of oil you use can differ depending on what type of climate you operate your vehicle in and how your vehicle is used (carrying big loads, towing, etc.). Your owner's manual contains several different recommendations based on these factors.  Your service advisor can recommend the right oil for your needs.  Like Shakespeare said, "Oil's well that ends well."

Arizona Auto and Radiator Repair
1255 E FRY BLVD
Sierra Vista, AZ 85635
520-459-2216
http://www.azautorepair.net

Steering You Right (Tie Rod End Replacement)

For drivers, S stands for safety.  And there are three other words that start with S that are all equally important: starting, stopping and steering. For your vehicle to be at its safest, all three functions must be in top shape. 

Steering is one of those things we take for granted.  After all, you turn the wheel and your vehicle changes direction. But sometimes you might notice your steering is a little off.  Maybe you've noticed you turn your wheel slightly and your vehicle doesn't turn. You may feel a little vibration in the wheel that increases when you go faster.  You may hear a little squeak from the wheels when you steer and you may notice your tires aren't wearing evenly.

These are signs that your tie rod ends may be failing. Tie rod ends help connect your vehicle's steering mechanism to the wheels.  They can wear out after you've hit one too many potholes or just from constant use.  They can cause sloppy steering and loose handling, and they should be replaced when they've reached the end of their life span.

If you notice any of these things happening on your vehicle, bring it in to us so a technician can check it out.  There are a couple of different types of steering, recirculating ball steering and the one most of the latest vehicles have, rack and pinion. When we replace your tie rod ends, we will remove and replace the old ones and adjust them to meet your vehicle manufacturer's specifications.

Tie rod ends should often be replaced in pairs, and your vehicle should be aligned afterwards.  Keep your steering working the way it's supposed to, and your vehicle will be sure to steer you right.

Arizona Auto and Radiator Repair
1255 E FRY BLVD
Sierra Vista, AZ 85635
520-459-2216
http://www.azautorepair.net